< scrollamount="2" scrolldelay="2" class="jianjie"> 煙台AG體育網電子科技有限公司主營磁翻板液位計,磁致伸縮液位計浮球液位計酸度變送器,等產品。是一家以科研開發、生產組裝、進口代理、工程設計、係統成套為一體的綜合性工業自動化高新技術企業。品種規格齊全,質量穩定,產品廣泛應用於石油、化工、電力、冶金、紡織、食品、軍工等行業。公司始終堅持“誠實首信、創新進取、品質第一、顧客至上”的經營理念。以一流的產品竭誠為廣大用戶提供優質的服務。
 
物位儀表
分析儀表
壓力儀表
溫度儀表
流量儀表
防腐儀表及配件
代理儀表
選礦自動化
 
 

聯係人:呂先生
電 話:0535-6931012 8261019
傳 真:0535-8261013
手 機:13863816598
郵 編:264000
郵 箱:mingke2007@163.com
地 址:山東省煙台市開發區黑龍江路1號
網 址:http://www.ytmingke.com

 
  新聞中心  
磁翻板液位計容易出現哪些問題?
網址:www.ytmingke.com 發布者:admin 發布時間: 閱讀:8528

磁翻板液位計常見問題與故障及注意事項磁翻板液位計常見問題與故障及注意事項為您解決一般常見的液位的問題與故障。現場調校中偶爾會發現浮子上下移動不夠靈活。這大多是由於安裝不當引起的,磁翻板液位計此時要注意上下法蘭的中心是否在一條線上,是否與水平麵垂直。一般來說,與水平麵夾角最好不小於87度,如果偏差較大,可能會影響浮子的順利移動。    液位計調校正常,投用後發現浮子在某一位置出現一段時間的“吸住”現象。這主要是液位計穿過鋼製平台安裝時,與鋼板距離過近產生的。因此,穿過鋼製平台安裝需要特別注意液位計連通管管壁與平台切割邊線的間距。煙台AG體育網、根據現場使用經驗,此間距在100㎜左右即能保證對磁性浮子不產生影響。    液位計現場投用時,要特別注意應先打開上部閘閥,後打開下部閘閥。玻璃管液位計這是由於液位計連通管的底部裝有保護浮子的止推彈簧,否則,大差壓的作用可能撞碎浮子導致液位計無法使用。    液位計投用一段時間後,出現浮子難以浮起且浮子移動不靈活的情況。這基本上是因為磁性浮子上沾有鐵屑或其他汙物造成的。可先排空介質,再取出浮子,消除磁性浮子上沾有的鐵屑或其他汙物即可。    如果因運輸或其他原因導致現場指示用的密閉玻璃管破裂,則可用國產玻璃管更換。但最好能抽真空。煙台AG體育網、重錘式料位計還要注意玻璃管是否垂直,以免影響指示器的指示。    液位計使用過程中,如果輸出信號產生頻繁擾動或有幹擾脈衝,就要檢查信號電纜屏蔽層是否可靠接地,工作接是電阻能否滿足要求。倘若幹擾仍然沒有完全消除,可用信號隔離器來解決。    液位計使用時尤其要注意,千萬不要用強磁鐵在連通管外上下拉動浮子進行檢查.否則會導致磁性浮子磁化而改變極性,甚至會使浮子磁性減弱,以致難以正常工作。    選用本安型液位計時,尤其要注意液位計與安全柵的阻抗是否匹配。由於此液位計電源電壓為14.5-36VDC,小於一般變送器的14.5-45VDC,故負載較大時不能正常工作
Magnetic level indicator is common problems and faults and matters needing attention of magnetic level gauge common problems and faults and the matters needing attention to solve the problem and fault common level for you. Field adjustment will occasionally find the floater moves up and down is not flexible. This is mostly due to improper installation, magnetic level gauge at this time to pay attention to whether the center of the upper flange and the lower flange in a line perpendicular to the horizontal plane, whether. In general, and the horizontal plane angle should not less than 87 degrees, if the deviation is big, may affect the smooth movement of the floater. Liquid level gauge adjustment is normal, after the commissioning of the float in a position that a period of "suck" phenomenon. This is mainly liquid level gauge through the steel platform installation, and the steel plate are too close to the. Therefore, through the spacing of steel platform installation should pay special attention to level meter pipe wall and platform of cutting edge. Yantai Mingke, according to the practical experiences, this distance in 100 mm or so to ensure that it does not affect the magnetic float. Using field level meter, special attention must be paid to open the upper valve, lower valve open. Glass tube level gauge which is due to the communicating pipe liquid level gauge is installed at the bottom of the protection float thrust spring, otherwise, the big differential effect may float level gauge cannot be used to crash. Liquid level gauge for use after a period of time, appear to float to float and float can not move flexibly situation. This is basically because the magnetic float stained with iron or other contamination caused by. Can first emptying medium, and then remove the float, eliminate magnetic float with some iron or other filth. If for transportation or other reasons for airtight glass field for indication tube rupture, usable domestic glass tube replacement. But the best vacuum. Yantai Mingke, hammer type material level meter also note glass tube is vertical, so as not to affect the indication. Liquid level meter in use process, if the output signal to generate frequent disturbance or interference pulse, it is necessary to check signal cable shielding layer is reliable grounding, grounding resistance can meet the requirements of the work. If the interference is still not completely eliminated, can be used to solve signal isolator. Pay particular attention to the liquid level gauge is used, do not use strong magnets in the connecting pipe to inspect pulling floater outside. Otherwise it will result in changing the polarity of magnetization and magnetic float, and even make the float magnetic weakened, so that it cannot work normally. The intrinsically safe level timing, with particular attention to the impedance level meter and safety grid matches. Because this level of the supply voltage is 14.536VDC, less than the general transmitter 14.545VDC, the load is large can not work normally
 
打印本頁 || 關閉窗口
AG打不開 AG8打不開 AG真人秀平台 AG亞遊電玩 AG視訊在哪裏靠譜